水烟解决方案板 - 深圳Rimyi Technology Co., 有限公司.

水烟解决方案板

Button-Controlled Output with Preheating E-Cig Solution Board

模型: RMY005

尺寸: 123.00(±0.2)×67.00(±0.1)毫米

低功率: 静止电流 <35μa

可调温度控制

短路保护, 过度保护, 低压保护

产品概述

This is an electronic cigarette circuit board that uses button knobs to adjust the output voltage and has LED light display and voice broadcast. 它主要由以下电路模块组成: MCU控制模块, 动力输出模块, digital tube display and LED light display, 充电管理模块, 和锂电池控制模块. The button adjustment module can recognize the user's button operation to smoke through LED and voice broadcast, 这样用户吸烟时可以理解设备状态.

功能亮点

信号处理: Identify user smoking by detecting button signals, and the MCU controls the output module to output heating after receiving the button signals.
User operation judgment: Identify user smoking by detecting key signals, and the MCU controls the output module to output heating after receiving the key signals.
保护功能: 该PCBA解决方案板具有多个保护功能，以确保使用过程中的用户安全, 包括锂电池保护功能, 吸烟超时保护, 过度保护, 短路保护, 和低电池保护.
模块形式: SMT包装用于形成模块表单, 这使其可以直接焊接到电路上, 使其非常适合PCBA集成, 从而降低组装成本并提高生产效率.

绝对最大评分	范围	象征	价值	单元
	电源电压 (电源电压)	电源电压	-0.3~13	V
	充电电压 (VCC)	VCC	-0.3〜6.5	V
	在输出电流	IAT	15	一个
	输出负载	rload	0.4	哦

性能参数	象征	范围	状况	最小	typ	最大限度	单元
	p	操作气压		- -	- -	- -	PA
	电源电压	工作电压		9.0V		12.75	V
	Vuvlo	低压检测阈值	VDD从高到低	8.8V	9	9.1	V
	智商	静电电流	节能模式	- -	30	35	微安
	RDSON	切换管传导阻抗	这里= 1a	- -	- -	- -	毫欧
	爱	LED输出电流		- -	- -	- -	毫安
	卢比	短路保护阈值		- -	0.3	- -	哦
	增值税	恒定平均电压输出	VDD = 4.2V, 输出空负载	- -	- -	- -	V
	rload	输出负载		0.3	- -	- -	哦
	Dmin	最小传导占空比	VDD = 4.2V	- -	- -	- -	%
	tsmoke	吸烟超时		- -	10	- -	S
	VCC	充电输入电压			5	6.5	V
	VFLOAD	浮动充电阈值电压		12.5V	12.6	12.7	V
	vtrkl	滴水流, 恒定流动	VDD从低到高	8.75	9	9.15	V
	我	充电电流	VCC = 5V	- -	3000	- -	毫安
	itrikl	trick流电流	VCC = 5V	- -	300	- -	毫安
	TSD	过热保护阈值		- -	90	- -	℃

LED/显示状态	工作条件	Voice+LED display
	Post	The LED light strip lights up in the order of red, green, and blue
	Pre-heating	Start up and enter preheating mode. Preheat according to the gear temperature for 5 minutes. During the preheating period, the LED strip indicator lights up at a rate of 7 scrolling lights per minute, and all lights up. The preheating end will be announced with a voice prompt. During the preheating process, the temperature can be adjusted at any time. After the preheating is completed, the light strip should follow a breathing cycle of 5.5 秒.
	Turn on/off	1. Power on: Press and hold the knob for 2 seconds to turn on the device, and the startup voice will be broadcasted. The indicator light on the strip will light up one by one from low to the current battery level.
	Gear temperature control function	2. Shutdown: Turn off the Changan knob for 2 秒, and the indicator light on the LED strip will turn off the battery's current level position one by one, and the shutdown voice will be broadcasted. "
	Standby function	1. Use the knob to adjust the temperature range between 180-330 ℃.
	过电流或短路保护	2. Rotate clockwise to increase temperature. The light strip lights up from both sides towards the middle to the set gear, and the color of the light strip is yellow.
	吸烟前电压欠压	3. Rotate counterclockwise to reduce temperature. The light strip turns off from the middle to both sides at the set gear, and the color of the light strip is yellow. "
	香烟照明后电压欠压	When not in use, the temperature drops by 5 degrees Celsius every 5 秒, with a maximum decrease of 20% of the set temperature and maintained.
	正常充电	Re suction the temperature and increase the full power to the set temperature. "
	电池充满电	- -
	释放充电 (卸下充电器)	- -

产品功能	It has a preheating function, which can preheat for a long time and has adjustable temperature control.
	在节能模式下: 静电电流<35 M A;
	工作电压: 8.5V~12.8V;
	支持宽电压充电 (4.5〜6.5V);
	包含保护功能，例如过热 (OTP), 欠压 (uvlo), 短路 (SCP), ETC;
	Equipped with LED light display function and voice broadcast function